Category Archives: PVC/ Connectors/ Bulbs/Adaptors
Assortment of Bullet Connectors with Container
Abox of assorted bullet style connectorsBuilding your own lighting system? If you are picky about doing the job right this is the kit. Connectors are the same as used by Honda, Yamaha
A pair of Male and Female Hitec connectors with 22 AWG wire
A pair of high quality Hitec Male and female connectors Golden plated to ensure very good contact. 6″ 22 Gauge silicone wire With pre-coated soldering for easy soldering Must have for making
Tamiya discharge banana plug connector for Tenergy LIPO car battery packs
Standard Tamiya discharge connector for battery packs for RC applications.
Conversion Cable 2-Hole Connector to Female DC conncetor
2-Hole universal female connector to DC female connector With 10″, 20AWG wire for extension.A conversion connection from 2-pin/2-hole connectors to standard DC connectors
10 AA Tenergy Plastic Cases for 4 AA Battery (Batteries sold separately)
10 AA Tenergy Plastic CasesPack of 10 AA Tenergy Brand clear plastic box for 4 AA Batteries Fits battery cells of 1-4 AA With clip to secure the batteries within the box
DC Female Connector with Bare Leads OD: 5.5mm ID: 2.5mm
Bare leads to female DC universal connector Wire length140mmOuter diameter5.5mmInner diameter2.5mm
DC Female Connector with Bare Leads OD: 4mm ID:1.75mm
Bare leads to DC universal connector Wire Length140mmOuter diameter4mmInner diameter1.75mm
DC Male Connector with Bare Leads OD: 5.5mm ID: 2.5mm
Male DC universal connector Outside diameter5.5mmInside diameter2.5mm
JST-XH V2 6 Pin Adapter for any 5 Cell Pack
This connector with wire leads is the same type found on V2 packs The wire leads can be spliced onto the balancing leads of any brand of 18.5 volt (5 cell) Li-Polymer
JST-XH V2 7 Pin Adapter for any 6 Cell Pack
This connector with wire leads is the same type found on V2 packs The wire leads can be spliced onto the balancing leads of any brand of 22.2 volt (6 cell) Li-Polymer
TX and RX Charge Cable Set for Futaba J
Banana plugs on one end with Futaba-style receiver and transmitter connectorson the other end. Use these two charge harnesses to charge your futabatransmitter and receiver batteries.
Tamiya charging banana plug connector for Tenergy LIPO car battery packs
Tamiya charging banana connector for Tenergy LIPO car battery packs
JST-XHP 2Pin Power Connector
Connector with wire leads 150mm 22 Gauge silicone wireBe sure to check the polarity before splicing.Incorrect polarity can cause permanent damage to a charger or balancer and may cause a fire.
JR / Futaba Receiver Switch AM-6003
JR / Futaba On/Off Receiver Switch 3 Plug with mounting plate and 2 screws.
Traxxas Charging Adapter to Standard Tamiya Connector
Traxxas high-current adapter is used to charge the batteries that are equipped with the Traxxas connector. Use this adapter to charge your Traxxas battery with your standard Tamiya plug equipped charger.Traxxas Male
Molex 5102 2 Pin Battery Side Connector for 1/18 Scale RC Car
High quality Molex 5102 2 Pin Battery Side Connector. 110mm 20 Gauge silicone wire With pre-coated soldering for easy soldering
16AWG Series Y-Harness Traxxas High-Current adapter
Traxxas Y-harnesses let you run dual-battery power for increased speedwith the proven convenience and performance of genuineTraxxas High-Current Connectors. Use the series harness adapter tocombine battery voltage and unlock the 50+mph speed
16AWG Parallel Harness Traxxas High-Current adapter
Traxxas Parallel harnesses let you run dual-battery power to double the capacity (runtime)with the proven convenience and performance of genuineTraxxas High-Current Connectors for your 1/16 E-Revo or Slash. PLEASE NOTEDual-battery operationrequires attention
